The NCRS (National Corvette Restorers Society) recently held an event in Lakeland Florida, February 24-26th. Corvette enthusiasts from around the country gathered to share their admiration of this timeless, classic car.
Read more
Posted in Corvette, C1 1953-62, General, C2 1963-67, General, C3 1968-82, General, C4 1984-96, General, C5 1997-04, General, C6 2005-13, General, C7 2014-19, General, C8 2020- and General
Read more
Posted in Corvette, Featured, Featured, Featured, Featured, Featured, Featured, Featured and Featured
All early Chevrolet Corvette factory exhaust manifolds are cast iron. Since the manifolds are cast, the actual casting number and date are raised above the actual surface of the part. Most casting numbers are visible when the manifold is installed on the engine. The casting number location and casting date location will vary from year to year and sometimes manifold to manifold. Some manifolds will not carry a casting date at all. Small block manifolds do not carry a year designation. 2" outlet small block manifolds will have a casting date, while most 2 1/2" outlet manifolds do not have a casting date. There were two types of manifolds being cast for Corvette, the first from the Flint, Michigan built engines, which were cast in Saginaw, Michigan. All small block Corvettes used these manifolds. The second type was cast at the Tonawanda Engine plant and all Corvette big block engines used these manifolds. The big block manifolds will be discussed and identified in the second installment of this article.
Read more
Posted in Corvette, C1 1953-62, Quick Tips, C2 1963-67 and Quick Tips
The camshaft is the one part of the internal combustion engine, which has the most bearing on how that engine will operate. The basic function of the camshaft is to control the timing, the length, the speed, and the height of the intake and exhaust valve openings inside the cylinder head. The camshaft in all Chevrolet engines is located within its own bearing chamber below the cylinder head face and above the oil pan rails. There have been some minor changes in rear camshaft bearing face design, but for the most part the camshaft has remained the same from 1955-82. It is important to verify which type of block, rear bearing face and camshaft bearing you need before you invest in a camshaft.
Read more
Posted in Corvette, C1 1953-62, Technical, C2 1963-67 and Technical
This article will focus on the different types of Corvette trim Tags that were used from 1955-1982. There were numerous changes over that period and we hope to cover the majority of those changes in this article. We will cover the rear differentials in brief detail to point out the specific differences that exist.
Read more
Posted in Corvette, C1 1953-62, Technical, C2 1963-67, Technical, C3 1968-82 and Technical
Read more
Posted in Corvette, C1 1953-62, Technical, C2 1963-67, Technical, C3 1968-82 and Technical
Read more
Posted in Corvette, C1 1953-62, Technical, C2 1963-67, Technical, C3 1968-82 and Technical
I’ve been a car guy since I was 11 and have owned several muscle cars…never a Corvette though. So, it made sense to buy a Vette so I could better understand our customers, the community, and hobby/lifestyle. After hours of research, I decided on a 2001 C5.
Read more
Posted in Corvette, Featured, Featured, Featured, Featured, C5 1997-04, Featured, Featured, Featured and Featured
The 1966 Sting Ray’s styling was very similar to the ’65’s, but there were some subtle changes. The Corvette “script” emblem was an elongated, more vertical style and was affixed to the hood and rear deck. The grille was now a plated, square mesh, cast unit. The roof B-pillar vents that had been both functional and non-functional in previous mid-year Corvettes (1964-1965) were now deleted. Another cool thing about the ’66? This was the intro year for the legendary 427!
Read more
Posted in Corvette, Featured, C2 1963-67, Featured, Featured, Featured, Featured, Featured, Featured and Featured
The 1965 Sting Ray marked the third year of “C2” production. All models were manufactured at GM’s St. Louis Assembly. 1965 was the first year a big-block engine would find its way between the fenderwells of a Corvette, in the form of a Mark IV 396 generating 425 horsepower. Styling changes included removing the hood depressions that were common to the 1963 and ’64 models. The horizontal grille bars were now black with the outer grille trim remaining bright – this made the ’65’s grille one of a kind. Also, the front fender “gills” now sported three functional, vertical slots.
Read more
Posted in Corvette, Featured, C2 1963-67, Featured, Featured, Featured, Featured, Featured, Featured and Featured